Daiichi Keiki Mfg GRK 甘油式輸入壓力計 G-AU1/4-60:0.3MPA 0354-01-0010020

NT$ 3,134NT$ 3,918
商品包含 1 種型號,請點選「立即選購規格」挑選

💡 重要通知:

因中東戰爭造成原物料波動影響,若訂單成立後進貨成本發生重大異動,我們將主動聯繫您協商處理。造成不便,敬請見諒。

登入即享專屬優惠價格
付款月結報帳 / 信用卡 / 銀行轉帳
運送宅配快速到貨,滿 NT$ 999 元即享免運!

選購型號

詳細規格與圖片請點選「商品型號」
商品型號ABP-67484761
GRK Glycerin Input Pressure Gauge G-AU1/4-60:0.3MPA
原廠型號 0354-01-0010020
滅菌無
諮詢/訂購後通知
1piece
NT$ 3,134NT$ 3,918
減少
增加

商品介紹

Features

  • With an endurance ratio of more than 30 times, the deflection of the pointer during operation is approximately 1/6. In addition, since it has the same mounting hole as the general product, it is interchangeable even when the conventional anti-vibration type is used. Glycerin solution is equivalent to class 4 and class 3 petroleum in the Fire Defense Law, so there is little risk of fire, and since it is harmless, it can be used for food industry.
  • [Notes]
  • Mount at approximately the same height as the measured convection. In the case of water, there will be an error of about 1/10 atmospheric pressure at a height of 1 m.
  • Mount horizontally or vertically. Be sure to specify the mounting position when only sideways or upside down mounting is possible.
  • For mounting, be sure to tighten with a specified tool such as a spanner, without screwing such as turning by holding the gauge body.
  • Typical installation locations are shown below. When the measuring object is gas, it is attached to the top of the measuring fluid container.
  • Steam is taken out from the side of the container through a siphon pipe, and drain cocks are installed at each part of the piping. The operating temperature range of the gauge is -5~45°C. Keep this in mind and pay attention to radiant heat. Separate the gauge or stand a shielding plate to avoid heat.
  • In the case of hydraulic pressure, take it out from under the container and attach an air vent to the crest of the piping.
  • Do not forget to insert a dampener because the instantaneous initial pressure when starting the pump may be several times the normal pressure and pulsating pressure may lead to fatigue failure. It is suitable to reduce the dampener's pulsating pressure to within one scale and to rise to the maximum pressure for approximately one second. It depends on the measuring fluid and pressure, but the standard for loosening the tightened screw is approximately 10~45°C.
  • The rubber stopper attached to the top of the gauge pops out when the internal pressure of the case rises to about 0.3~0.4 MPa. Leave at least 10 cm of space around the plug.
  • If possible, it is better to install a safety valve at an appropriate place in the piping. In this case, take special care to avoid any danger when installing the product.

Specification

  • Case External Shape: A Type
  • Magnitude: Φ60
  • Connecting Screws: G1/4
  • Accuracy: ±1.6%%%% F.S
  • Pressure span: 0~0.3MPA
  • Material: Connection Part Material; Brass/Case Material; Aluminum Silver Plated Case
  • Securities Code: 119-0170688
以上圖片及相關資訊由 AS ONE 提供。
若有現場安裝、說明或特殊配送需求,歡迎事前與科研市集聯繫。部分商品因供應條件限制,可能無法提供相關服務,敬請見諒。
有任何商品上面的問題?
別擔心,讓科研市集來為你服務!
立即諮詢客服
最懂你的專屬採購模式
需要單位的最優價格及服務嗎? 我們的專業團隊能幫到你!
前往了解方案
購物車